Reprogrammation Keyfob Corvette C6

Voici les procédures à suivre :

Method 1 - Key Fob Quick Learn

This procedure will add key fobs. Fobs will be numbered in sequence
based on when they are programmed; if 2 fobs are currently programmed to
the RCDLR, a fob programmed using this method will be numbered as Fob
3. This procedure requires that you have a known good key fob, a
replacement key fob, and the vehicles mechanical key.

Important: This procedure is not available when the maximum number of
fobs (4) have been programmed. If 4 key fobs are programmed to this
RCDLR and this method is attempted, the driver information center (DIC)
will display MAX FOBS LEARNED and the programming procedure will exit.
Method 4 must be used in this instance.

1. The vehicle must be OFF.
2. Open the rear compartment.
3. Place a known key fob within the interior of the vehicle.
4. At the rear of the vehicle insert the vehicle key in the rear
compartment lock cylinder located in the lower left and cycle the key 5
times within 5 seconds.
5. The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or
4).
6. Place the replacement key fob in the glove box fob pocket with the
buttons facing right.
7. A beep will occur and the DIC will display: READY FOR FOB X (X =
fob 3 or 4) or MAX FOBS LEARNED.
8. If programming additional key fobs, repeat steps 5 and 6, or press
the OFF/ACC portion of the ignition switch to exit programming mode.
9. Operate the active portion of each key fob to exit the programming
and to verify correct system operation.


The number on the fob doesn't have anything to do with Driver Number. If
you are wanting to change your fobs so that Fob 1 corresponds to Driver
1, I believe you will have to go to the dealer and hook it up to a Tech
II.


Method 2 - Key Fob Slot Programming

This procedure will add or replace a key fob. Method 2 allows you to
choose which location (slot) the unprogrammed fob will be learned to. If
you are replacing a key fob, this method will erase the previously
known key fob programmed to that particular slot. This procedure
requires that you have a known good key fob, a replacement key fob, the
vehicle mechanical key, and a scan tool.

Important: This procedure is not available when the maximum number of
fobs (4) have been programmed. If 4 key fobs are programmed to this
RCDLR and this method is attempted, the DIC will display MAX FOBS
LEARNED and the programming procedure will exit. Method 4 must be used
in this instance.

1. The vehicle must be OFF.
2. Open the rear compartment.
3. Place a known key fob within the interior of the vehicle.
4. At the rear of the vehicle insert the vehicle key in the rear
compartment lock cylinder located in the lower left and cycle the key 5
times within 5 seconds.
5. Install a scan tool.
6. Use the scan tool, to access the following:
• Vehicle Control Systems
• Computer/Integrating Systems
• Module Replacement/Setup
• RCDLR
• Program Key Fobs
7. Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be
the slot you wish to program to.
8. Place the replacement key fob in the glove box pocket with the
buttons facing right. A beep will occur indicating programming
completion. The previously known fob is now erased.
9. If programming additional key fobs, repeat steps 4-8, or press the
OFF/ACC portion of the ignition switch to exit programming.
10. Remove the scan tool.
11. Operate the active portion of each key fob to exit the programming
and verify correct system operation.

Pour info:

La procédure notée si dessus fonctionne pour une version U.S. (elle est d'ailleurs dans le manuel utilisateur) par contre elle ne fonctionne pas sur une version Europe! (et elle ne figure pas dans le manuel français).

Donc ne perdez pas votre temps à essayer en tournant 5 fois votre clé dans la serrure du coffre...

vous n'aurez aucun affichage sur le DIC